Still have a little green-stuff work to do on the marine's respirator attachment, but for all intents and purposes it's done. Now I need to figure out what the regular CSM's Rhino will look like. I've got some IG dozer blades lyin' 'round here somewhere...
Saturday, September 24, 2011
Thursday, September 15, 2011
The dozer blade is magnetized. Still need to trick out the doors, shave the IW logo down a bit, add the IW stickin' out the top, and then get down to detail work. I've got some spikes and barbed wire lying around that I'd like to use if I can make it look good...
Sunday, September 4, 2011
The Breaching Squad's Rhino is nowhere near complete, but it's on its way. Here's a teaser...
All I'll say is this: the front plate takes queues from the IW Rhino Doors kit and I have a rapidly growing knowledge-base concerning InstantMold...
I also pulled out some Blue-Tac and fit the squad together partially to test the fit, and partially to get some better shots of what the squad will look like. All of the following pics are clickable to a double-sized version.
I mentioned in the first post that I had to modify the Mk. III shoulder pads quite a bit, so I went ahead and got some pics of that too. With three horned-helm exceptions, two of which were necessary due to positioning, the "Legion" pad above goes on a Marine's right shoulder. Two figures have FW pads on both shoulders. I'm mixing and matching as I go, trying to steer clear of any 8-pointed stars. These guys aren't intended to be pre-Heresy, but I want them to be Iron Warriors first, Chaos Space Marines second.
As always, questions, comments, criticism both welcomed and encouraged.
Thursday, September 1, 2011
|Iron Warriors Combat Patrol: 400 points|
And, after a few days intermittent work, here's where I'm at with 'em...
Breach Squad: close support and flamers
Breach Squad: plasma, ranged support, aspiring champ
I was a little gunshy about mixing the FW and GW parts, as neither are cheap and if it looks ass I've only myself to blame. Test fits looked promising so I went ahead with it. There are problems, though. The plastic heads fit low in the FW bodies, and, somehow, the FW heads fit low in the plastic bodies. A little grey-stuff spacer fixed the problem in both cases. There's also compatibility issues between the resin torsos and plastic legs - not enough contact area for glue to adhere. Once again, this is easily fixed with a little grey-stuff.
The Mk.III arms are all identical, and, IMO, are the most awkward arm pose from any Space Marine box - the downward tilt. All the SM/CSM Troop boxes have at least one set of those arms. The Mk.III greaves have the additional problem that their ornamentation can make it hard to find a good pose, even on the Mk.III torsos they come with. You can work around it, but I suggest gluing the "fist arm" flush into position with your weapon held at the angle you want, let it dry, then glue the "grip arm" with your weapon in place so you get a nice fit. If you glue both arms completely flush to the torso, the fist and grip will likely be too close to look right.
The Mk.III shoulder pads fit like regular shoulder pads, but have a few problems integrating with the CSM kits. There are a couple arm position/head combos that make it impossible to fit the tall, ornate Mk.III pads underneath a horned helm without alteration. Likewise, they flat out cannot fit on the bent pistol arm without modification. When I cut them down to fit the pistol arm, I liked the look so much I went ahead and altered all of them to match, even though they fit as-is on all the bolter/special weapon marines. I'll try to get some close-up pics of the alteration(s) later.
Considering how easy it is to kit out Chosen and Havocs with special weapons, the CSM box is woefully lacking. Trying to stay thrifty, I've Chaos-ified some "borrowed" from loyalist sources. Don't think they look too bad, considering.
Those that have seen the list may wonder why there's 10 dudes above. I figured I'd go ahead and make/paint both squads at full-strength, just in case I fall in love with the Iron Warriors and have to flesh it out further. I've Army Buildered the list out to 2300ish just grabbing what I think are fluffy Codex options. And I've still got two Troop and all the FA to fill! With that in mind, I've also begun work on a model that I can't even use in Combat Patrol...
Chaos Lord: daemon weapon, combi-melta
The sword's being held in place, as it's being held by the wrong hand. I've also got to a little grey-stuff work to add flexible joint armour and smooth out some of the nastier exacto cuts it took to trim this guy down to something useable. Also need to prop and angle the head a bit - in the pic it's being held by gravity.
Anyway, that's the start of the force. I've got a Rhino on sprue sitting next to me that needs some attention. As always, questions, comments, and criticism both welcome and encouraged.